How to Test Your Microphone Online (and Fix It)

📄 6 min readUpdated November 17, 2026

Open the microphone test, press Start, allow the browser prompt, and talk. If the bar moves and the status says "Mic is picking up sound", the microphone works. Then record the 5-second clip and play it back, because a moving bar only tells you there's a signal, not that it sounds right.

How do you test a microphone online?

  1. Open the microphone test and press Start microphone test. Allow the permission prompt. Browsers must ask at least the first time.
  2. Speak at your normal call volume and watch the input level bar and the percentage under it.
  3. Press Record 5s clip, say a full sentence, and listen to the playback that appears.
  4. Read the small table below the buttons. It lists the device name, sample rate, channels, and whether echo cancellation, noise suppression and auto gain control are on.

Don't skip the device name row. A laptop with a headset or webcam attached has several inputs, and the browser may have opened the wrong one. If the name isn't the mic you're talking into, that's your answer.

What should the input level look like?

The bar should jump when you talk and fall back when you stop. The percentage isn't a volume setting or decibels. The tool takes the average strength of the waveform (its RMS value), multiplies it by 300, and caps it at 100. Here's what each reading stands for, computed from that formula.

Meter readingSignal level (RMS, dB below full scale)What the tool does
0 to 4%below -35.6 dBCounts it as silence. After about 80 quiet frames in a row it shows "No signal detected"
5%-35.6Status flips to "Mic is picking up sound"
10%-29.5Clearly registering
30%-20.0Bar is about a third full
50%-15.6Bar is half full
100%-9.5 or louderBar is pinned. Anything above a third of full scale reads the same

The bar fills completely once the signal reaches a third of full scale, so loud speech close to the mic can pin it without anything being wrong. A steady 1 to 4% with nobody talking is background noise, and the tool doesn't count it.

We haven't measured where normal speech lands on different microphones, so don't chase a target number. Look for movement that tracks your voice, then trust the playback.

Why isn't my microphone picking up sound?

There are two different failures. Either the browser couldn't open the mic at all and you get a red error, or it opened one and hears nothing, so the bar sits at 0%. For the first kind, the tool turns the browser's error into a plain message. The error names are the standard ones documented by MDN.

What you seeBrowser error behind itWhat it meansFirst thing to try
Microphone permission deniedNotAllowedErrorYou or a browser setting refused access, or the page isn't on HTTPSAllow the microphone for the site, then check the OS privacy switch
No microphone foundNotFoundErrorThe browser found no audio input at allPlug in the mic or headset, or enable the built-in one in sound settings
Microphone in use or unreadableNotReadableErrorPermission was granted, but a hardware error at the OS, browser or page level blocked accessClose other apps that use the mic, replug the device, press Start again

A flat 0% with no error means the stream is open and delivering silence. Check these:

If the failing mic is built into a webcam, Microsoft says to check the camera privacy setting too. The webcam test confirms the camera half.

Where are the microphone settings on Windows, Mac and in the browser?

Permission lives in two layers. The operating system decides whether your browser may use the mic, and the browser decides whether a site may. Both have to say yes. These paths come from Microsoft's, Apple's and Google's help pages.

WherePathWhat to check
Windows 11 privacyStart > Settings > Privacy & security > Microphone"Microphone access" and "Let apps access your microphone" are on, plus "Let desktop apps access your microphone" (browsers are desktop apps)
Windows 11 inputStart > Settings > System > Sound, under InputThe right device is picked; open it, press "Start test", and adjust "Input volume"
Windows 10Start > Settings > Privacy > Microphone, then System > SoundThe same two access switches; Device Properties > Levels for the volume sliders
Mac privacyApple menu > System Settings > Privacy & Security > MicrophoneYour browser is switched on in the list
Mac inputApple menu > System Settings > Sound > InputThe right device is selected; drag the input volume slider
ChromeMore > Settings > Privacy and security > Site settings > MicrophoneThe site isn't blocked; the Down arrow picks the default microphone
SafariSafari > Settings > Websites > MicrophoneThe site is set to Ask or Allow, not Deny

Firefox isn't in the table because we couldn't load Mozilla's help page to confirm its menu path.

Why is my mic too quiet?

If the bar moves but barely clears 5%, the mic works and the gain is low. Raise the input volume in the Sound settings above. Windows 10 also has a "Microphone Boost" slider on the Levels tab. Then move closer to the mic and test again.

Check the auto gain control row as well. When it's on, the level is adjusted for you. Our tool doesn't request it either way, so you're seeing your browser's default.

If the bar looks healthy here but callers say you're faint, the call app is probably using a different input. Compare its audio settings with the device name this test shows.

What causes echo, static and background noise?

Echo is your microphone hearing your own speakers. Echo cancellation removes sound the computer itself is playing from what the mic records, and noise suppression is meant to cut background noise. The microphone test requests both, and the settings table tells you whether your browser actually applied them. A request is only a preference, so the browser may ignore it.

That matters for the playback clip: you're hearing the processed signal, not the raw microphone. If word endings sound clipped or slightly underwater, suspect the processing before you blame the mic.

If you still hear echo, wear headphones. That removes the speaker sound at the source. The speaker test plays left and right tones. For static or crackle, try another USB port or cable first.

Frequently Asked Questions

How do I know if my microphone is working?

Start the microphone test, allow access and speak. If the level bar rises when you talk and the status reads Mic is picking up sound, the mic works. Then play back the 5-second clip to confirm it sounds clear.

Why does the mic test show 0% when I talk?

The browser opened a microphone but it is delivering silence. Check for a mute button on the headset, read the device name row to see which input was opened, and raise the input volume in your system sound settings.

Does the microphone test record or upload my voice?

No. The level is measured inside the page, and the optional 5-second clip is kept only in the browser tab so you can play it back. Pressing Stop releases the microphone.

What does the percentage on the mic meter mean?

It is the average signal strength multiplied by 300 and capped at 100, not a volume setting or a decibel value. The tool treats 5% and up as sound. A reading of 100% means the signal is at about a third of full scale or louder.

Why can people hear an echo when I speak?

Your microphone is picking up your own speakers. Echo cancellation in the browser or call app usually removes it, and the settings table in the test shows whether it is on. Wearing headphones fixes it at the source.

Related Tools