How to Test a Monitor for Backlight Bleed, IPS Glow and Banding

📄 6 min readUpdated November 18, 2026

Open the screen test, pick the Black fill, and look at the edges and corners of the screen. Pale patches that stay put when you move your head are backlight bleed. A corner glow that shifts as you move is IPS glow, which is normal. Before you judge either, set the room and the brightness the way the manufacturers do, because a pitch-dark room makes almost every LCD look bad.

How do you test a monitor for backlight bleed?

  1. Let the display warm up. Dell's guidance is about 30 minutes.
  2. Keep some light on in the room. Dell says ambient lighting should be "slightly lit rather than being dark".
  3. Set brightness to roughly 30% to 50% of maximum, and sit at about arm's length with the screen at eye height.
  4. Open the screen test and press Black. The page goes fullscreen.
  5. Scan the four edges, then the corners. Move your head left, right, up and down and watch whether the pale areas move with you.
  6. Press Esc or click anywhere to leave, then run the other fills.

Those setup numbers come from Dell's article on telling IPS glow from light leakage. They're written for Dell monitors, but they suit any LCD. The test only draws colored fills, so your eyes do the judging.

Which fill shows which problem?

FillBest forWhat a problem looks like
BlackBacklight bleed, IPS glow, bright stuck pixelsPale patches along edges or in corners; a lit dot
WhiteDark pixels, dirt, tintA black speck; a yellow or pink cast on one side
Mid grayUneven brightness, faint ghost imagesCloudy blotches, darker bands, an outline of something that used to be on screen
Red, Green, BlueStuck or dead sub-pixelsA dot that doesn't match the fill
Uniformity gridComparing regionsSame-shade columns that look different from one side to the other
GradientColor bandingVisible stripes where the color should fade smoothly

Don't skip Mid gray. It sits near the middle of the range (128 out of 255), so cloudy patches and leftover ghost images stand out on it in a way they don't on black or white.

For single-pixel faults, use the dead pixel test, and see our guide on dead pixels versus stuck pixels for what makers will and won't replace.

What's the difference between backlight bleed and IPS glow?

They look alike on a black screen and they aren't the same thing. This comparison is taken from Dell's knowledge base article 000318297, last modified August 12, 2026.

IPS glowLight leakage (backlight bleed)
What Dell says it isA faint glow around the edges when viewed from certain anglesUneven backlight distribution
When you move your headChanges with viewing angle and distanceStays constant regardless of angle and distance
WhereMainly the cornersAnywhere along the edges or corners
CauseAn inherent trait of IPS technologyA manufacturing issue that can occur in any LCD panel type
A defect?NoIt can be, if it significantly affects the viewing experience

So the head-movement check in step 5 is the whole test. Glow that fades or slides when you lean to one side is IPS glow. A bright patch that sits in the same place from every angle is leakage.

How much backlight bleed is normal?

No maker we read publishes a number for it. What Dell does publish is the conditions it inspects under. Its laptop article says screens are checked in "normal office lighting conditions (150-200 lux)" and labels a dark room an incorrect inspection environment, because your eyes become more sensitive in the dark and any leakage looks worse.

The same article draws the line this way:

Dell's own checks are worth copying. Look at the screen in a normally lit room from where you usually sit. Show a white background and move the brightness up and down. If you have a second unit of the same model, compare the two at the same brightness. If the patch is still obvious, photograph it in normal lighting before you contact support. Other brands set their own rules. We've only read Dell's.

What does the uniformity grid show?

The grid splits the screen into 36 cells, six across and six down, in three shades of gray. The shades are 28, 88 and 148 out of 255, which is about 11%, 35% and 58% of full signal, and they repeat in columns, so each shade appears 12 times.

Compare cells of the same shade. The dark column on the far left should look like the dark column right of center. If one is visibly lighter or tinted, brightness isn't even across the panel. It's a by-eye comparison, not a measurement.

What does banding on the gradient mean?

The Gradient fill is a diagonal rainbow that runs red, yellow, green, cyan, blue, magenta and back to red. Each of its six sections changes one color channel through its full range. On a display showing all 256 levels per channel (16,777,216 colors), each step is so narrow you can't pick it out. We worked out the widths from the gradient's geometry:

ScreenBand width with 256 levels per channel (8-bit)Band width with 64 levels (6-bit)
1920 x 10801.4 px5.6 px
2560 x 14401.8 px7.5 px
3840 x 21602.8 px11.2 px

If you see clear stripes several pixels wide, fewer levels are reaching the screen than the signal contains. That can be the panel, but check software first: a night-light or color filter, a remote desktop session, or a low color setting in the graphics driver can all cause it. The browser test shows the color depth your browser reports.

One limit: this is a hue gradient, not a black-to-white ramp, so it won't show banding in dark grays.

Do OLED screens get backlight bleed?

No. An OLED has no backlight, so a black fill should be evenly black. What OLEDs can show is a leftover image. Apple's support page for its OLED iPhones calls both effects expected behavior. It says image persistence "is temporary and disappears after a few minutes of normal use", and that burn-in can occur "when the same high-contrast image is continuously displayed" for a long time.

To look for it, use Mid gray and check for the faint outline of a taskbar, dock or status bar. If it's gone after a few minutes of ordinary use, it was persistence.

Testing a whole machine? Run the keyboard test next.

Frequently Asked Questions

How do I check my monitor for backlight bleed?

Open the screen test, choose the Black fill and look along the edges and corners. Keep the room slightly lit and brightness at about 30% to 50%. Pale patches that stay in the same place when you move your head are backlight bleed.

Is backlight bleed normal?

Some is. Dell says edge light that is only clearly visible in darkness is within normal range, and that hot spots visible in normal room lighting are outside its specifications. Other brands set their own rules, so check your warranty terms.

What's the difference between IPS glow and backlight bleed?

IPS glow changes as you change your viewing angle or distance and mainly shows in the corners. Backlight bleed stays the same from every angle and can appear anywhere along the edges. Dell describes glow as a trait of IPS panels, not a defect.

Should I test for backlight bleed in a dark room?

Not if you want a fair result. Dell inspects laptop screens at 150 to 200 lux, which is normal office lighting, and calls a dark room an incorrect inspection environment. Your eyes get more sensitive in the dark, so any leakage looks worse.

Can OLED screens have backlight bleed?

No, because OLED panels have no backlight. They can show temporary image persistence or, in more extreme cases, burn-in. A mid gray fill is the easiest way to spot a leftover image.

Related Tools